License plate holder including insert frame with TÜV (suitable for Harley-Davidson models: Sportster S from 2021)

The Cult-Werk LED lighting set 3in1 including holder suitable for Harley-Davidson Sportster S models from 2021 onwards!! The holder on the outside contains the LED 3in1 lighting including E -Approval mark was made of steel and then glossy black. powder coated. The lighting unit is required if you remove the original lighting bracket and use a side license plate holder. The holder is screwed to the original mounting points in the rear section using the mounting material provided. The LED lighting must then be wired! The license plate holder witha milled plate including an insert frame for the license plate. Suitable for allHarley-Davidson Sportster S models from 2021 including GTü partial report! The shortest license plate holder on the market guarantees you a TOP look! The Cult-Werk license plate holder is made of high-quality steel, CNC lasered and then powder-coated black! Incl. LED license plate lighting with E-test mark. License plate size:  W-180xH-200 mm (suitable for Germany) or W-210xH-170 mm (suitable for Austria) other sizes with insert frames will follow... The assembly is very simple, the license plate holder is attached to the swing arm at the top hole of the original lighting bracket attached. A suitable screw is required, which is of course included in the scope of delivery! Since the Cult-Werk license plate holder has an extra short mounting foot compared to other license plate holders available on the market, it is visually much more appealing! Scope of delivery: - 1x side license plate holder - 1x LED license plate light incl. E-test mark (pre-assembled!) - 1x M8 screw - 4x screws incl. nuts for license plate fastening THE ASSEMBLY INSTRUCTIONS AND THE PARTS REPORT ARE AVAILABLE IN THE "DOWNLOADS" TAB!!!

Suitable for allHarley-Davidson Sportster S models from 2021 including GTü parts certificate! The shortest license plate holder on the market guarantees you a TOP look! The Cult-Werk license plate holder is made of high-quality steel, CNC lasered and then powder-coated black! Incl. LED license plate lighting with E-test mark. License plate size:  W-180xH-200 mm (suitable for Germany) or  ; W-210xH-170 mm (suitable for Austria) or  W-180xH-140 mm (suitable for Switzerland) or  W-170xH-170 mm (suitable for √ºfor Italy) orW-210xH-130 mm (variant 2 suitable for France) orW-210xH-140 mm (suitable for Netherlands) The assembly is Very simple, the license plate holder is attached to the swingarm at the top hole of the original lighting bracket. A suitable screw is required, which is of course included in the scope of delivery! Since the Cult-Werk license plate holder has an extra short mounting foot compared to other license plate holders available on the market, it is visually much more appealing! Scope of delivery: - 1x side license plate holder - 1x LED license plate light incl. E-test mark (pre-assembled!) - 1x M8 screw - 4x screws incl. nuts for license plate fastening THE ASSEMBLY INSTRUCTIONS AND THE PARTS REPORT ARE AVAILABLE IN THE "DOWNLOADS" TAB!!!

The Cult-Werk LED lighting set 3in1 including holder suitable for Harley-Davidson Sportster S models from 2021 onwards!! The holder on the outside contains the LED 3in1 lighting including E -Approval mark was made of steel and then glossy black. powder coated. The lighting unit is required if you remove the original lighting bracket and use a side license plate holder. The holder is screwed to the original mounting points in the rear section using the mounting material provided. The LED lighting must then be wired! The license plate holder for allHarley-Davidson Sportster S models from 2021 including GTü parts certificate ! The shortest license plate holder on the market guarantees you a TOP look! The Cult-Werk license plate holder is made of high-quality steel, CNC lasered and then powder-coated black! Incl. LED license plate lighting with E-test mark. License plate size:  W-180xH-200 mm (suitable for Germany) or  W-210xH-170 mm (suitable for Austria) or  W-180xH-140 mm (suitable for Switzerland) or  W-170xH-170 mm (suitable for Italy ) orW-210xH-130 mm (variant 2 suitable for France) orW-210xH-140 mm (suitable for the Netherlands) The assembly is very easy, the license plate holder is attached to the swingarm at the top hole of the original lighting bracket. A suitable screw is required, which is of course included in the scope of delivery! Since the Cult-Werk license plate holder has an extra short mounting foot compared to other license plate holders available on the market, it is visually much more appealing! Scope of delivery: - 1x side license plate holder - 1x LED license plate light incl. E-test mark (pre-assembled!) - 1x M8 screw - 4x screws incl. nuts for license plate fastening THE ASSEMBLY INSTRUCTIONS AND THE PARTS REPORT ARE AVAILABLE IN THE "DOWNLOADS" TAB!!!

The Cult-Werk side license plate holder with silent block bearing as well as GTü parts certificate for the listed license plate sizes and countries - including insert frame. Suitable for all Harley-Davidson Sportster models! (IMPORTANT: The holder fits 100% of Sportster models from the year 2000 onwards. For older models, please check beforehand whether the model is listed based on the area of use so that no problems arise when registering!)< /p> Since the unsprung masses of Sportster models are particularly high, many of the license plate holders available on the market break. The silent block reduces these to a minimum and a long service life is guaranteed! The shortest license plate holder on the market guarantees you a TOP look! The Cult-Werk license plate holder is made of high-quality steel, CNC lasered and then powder-coated black! Incl. LED license plate lighting with E-test mark. License plate size:  W-180xH-200 mm (suitable for Germany) or W-210xH-170 mm (suitable for Austria) other sizes with insert frames will follow... The assembly is very easy, the license plate holder is included screwed to the lower shock absorber mounting screw. This requires a longer screw, which is of course included in the scope of delivery (screw must be shortened if necessary). Since the Cult-Werk license plate holder has an extra short mounting foot compared to other license plate holders available on the market, it is visually much more appealing! Scope of delivery: - 1x side license plate holder incl. insert frame - 1x LED license plate light incl. E-test mark (pre-assembled!) - 1x pan head screw, similar. ISO7380 ¬Ω‚Äú-20UNFx3.5‚Äú, 10.9 - 2x grub screws for license plate fastening THE ASSEMBLY INSTRUCTIONS AND THE PARTS REPORT ARE AVAILABLE IN THE "DOWNLOADS" TAB!!! < p>

The Cult-Werk side license plate holder with GTú parts certificate for the listed license plate sizes and countries as well as a milled plate including insert frame for the license plate!Suitable for all Harley-Davidson Breakout models from 2013 to 2017 and also suitable for Harley-Davidson< sup> Rocker models from 2008 to 2011! The shortest license plate holder on the market guarantees you a TOP look! The license plate holder from Cult-Werk is made of high-quality steel, CNC lasered and then powder-coated black! Incl. LED license plate lighting with E-test mark. License plate size:  W-180xH-200 mm (suitable for √ºfor Germany) orW-210xH-170 mm (suitable for √Austria) other sizes with slide-in frames will follow... Installation is very simple, the license plate holder is screwed onto the rear axle. This requires a special nut with collar, which is of course included in the scope of delivery. Since the Cult-Werk license plate holder has an extra short mounting foot compared to other license plate holders available on the market, it is visually much more appealing! Scope of delivery : - 1x side license plate holder incl. insert frame - 1x LED license plate light incl. E-test mark (pre-assembled!) - 1x special stainless steel nut with collar M24x1.5 - 2x grub screws for license plate attachment THE ASSEMBLY INSTRUCTIONS AND THE PARTS REPORT ARE AVAILABLE IN THE "DOWNLOADS" TAB!!! < /p>

The Cult-Werk side license plate holder with silent block bearing as well as GTü parts certificate for the listed license plate sizes and countries - including insert frame. Suitable for all Harley-Davidson Nightster models from 2022 onwards! The shortest license plate holder on the market guarantees you a TOP look! The license plate holder from Cult-Werk is Made of high-quality steel, CNC lasered and then black powder-coated! Incl. LED license plate lighting with E-test mark. License plate size:  W-180xH-200 mm (suitable for Germany) or W-210xH-170 mm (suitable for Austria) other sizes with insert frames will follow... The assembly is very easy, the license plate holder is included screwed to the lower shock absorber mounting screw. This requires a longer screw, which is of course included in the scope of delivery (screw must be shortened if necessary). Since the Cult-Werk license plate holder has an extra short mounting foot compared to other license plate holders available on the market, it is visually much more appealing! Scope of delivery: - 1x side license plate holder incl. insert frame - 1x LED license plate light incl. E-test mark (pre-assembled!) - 1x pan head screw, similar. ISO7380 70.9 M12x70 - 2x grub screws for license plate fastening THE ASSEMBLY INSTRUCTIONS AND THE PARTS REPORT ARE AVAILABLE IN THE "DOWNLOADS" TAB!!!

The Cult-Werk side license plate holder with GT√ú parts certificate for the listed license plate reasons and countries as well as a milled plate including insert frame for the license plate.  Suitable for all Harley-Davidson Dyna models (Street Bob, Street Bob Special, Low Rider, Wide Glide, Fat Bob & Switchback) from the year of manufacture 2008 to the last year of manufacture 2017! The shortest license plate holder on the market guarantees you a TOP look! The Cult-Werk license plate holder is made of high-quality steel, CNC lasered and then powder-coated black! Incl. LED license plate lighting with E-test mark. License plate size:  W-180xH-200 mm (suitable for √ºfor Germany) orW-210xH-170 mm (suitable for √Austria) other sizes with slide-in frames will follow... Installation is very simple, the license plate holder is screwed onto the rear axle. This requires a special nut with collar, which is of course included in the scope of delivery. Since the Cult-Werk license plate holder has an extra short mounting foot compared to other license plate holders available on the market, it is visually much more appealing! Scope of delivery : - 1x side license plate holder with insert frame - 1x LED license plate light incl. E-test mark (pre-assembled!) - 1x special stainless steel nut with collar M24x2- 1x Anti-twist protection using a worm screw - 2x grub screws for license plate attachment THE ASSEMBLY INSTRUCTIONS AND THE PARTS APPROVAL ARE IN THE DOWNLOADS TAB PROVIDED!!!

The Cult-Werk side license plate holder with GTú parts certificate for the listed countries as well as greens and a milled plate including insert frame for ºfor the license plate. Suitable for all Harley-Davidson Softail models - not for the FXDR 114 - from Year of construction 2018! (Street Bob, Low Rider, Fat Bob, Softail Slim, Softail Deluxe, Breakout, Fat Boy, Sport Glide & Heritage Classic - IMPORTANT: With the Sport Glide & Heritage Classic, the license plate holder can only be used without the cases be used!) The shortest license plate holder on the market guarantees you a TOP look! The license plate holder from Cult-Werk is made of high-quality steel, CNC Lasered and then powder-coated black! Incl. LED license plate lighting with E-test mark. License plate size:  W-180xH-200 mm (suitable for √ºfor Germany) orW-210xH-170 mm (suitable for √Austria) other sizes with slide-in frames will follow... Installation is very simple, the license plate holder is screwed onto the rear axle. This requires a special nut with collar, which is of course included in the scope of delivery. Since the Cult-Werk license plate holder has an extra short mounting foot compared to other license plate holders available on the market, it is visually much more appealing! Scope of delivery : - 1x side license plate holder incl. insert frame - 1x LED license plate light incl. E-test mark (pre-assembled!) - 1x special stainless steel nut with collar M24x2 - 2x grub screws for license plate attachment THE ASSEMBLY INSTRUCTIONS AND THE PARTS REPORT ARE AVAILABLE IN THE "DOWNLOADS" TAB!!! < /span>